Test weg

stock removal vs. forging - Whats better in knife making? Die Frage, was von beiden besser ist, wird unter Messermachern immer wieder diskutiert - an Ende der Forenbeiträge und der Youtube-Videos ist die Antwort ist immer die selbe: Kommt `drauf an, was du möchtest und was dir möglich ist! Willst du harte körperliche Arbeit, große Hitze und mit dem dicken Hammer auf den Amboss schlagen, dass die Dezibel und die Flunken nur so fliegen? Du möchtest dein Material komplett selbst herstellen und nimmst dafür mehr Arbeit und etwas Unsicherheit bzgl. der Materialeigenschaften und -Zusammensetzung in Kauf? Du hast Zugang zu einer Esse samt Abzug und die Anwohner beschweren sich nicht über Lärm? Dann bist du beim forging knife making richtig aufgehoben.
Wenn du das alles nicht möchtest oder die Rahmenbedingungen nicht erfüllt werden oder du einfach nur mal Bock auf etwas Anderes hast, dann bist du bei der stock removal method richtig aufgehoben. Obendrein erhältst du nach der Wärmebehandlung eine Messerklinge mit reproduzierbaren Ergebnissen und arbeitest mit Stählen, deren Legierungsbestandteile - und vor allem der qualitätsentscheidende Kohlenstoffanteil - definiert sind. Außerdem werden die zugekauften Stähle natürlich ebenso durchgeschmiedet. Nur eben nicht von Hand, sondern in einer hochspezialisierten (meist japanischen) Fabrik.

In meinen Messerkursen wende ich ausschließlich die stock removal-Methode an.

Von osirisgems.com

 

Auch das hier ist eine Gute Edelsteinseite: 

What is the difference between a gem and a precision faceted gem? And why is it worth to take care about?
This site will show you what is a high valuable gem with investment potential.

Everyone knows about  the  first 3 facts of the 4C´s
Carat, Clarity, Color & ?
But it´s much harder to take account of the last C = Cut.
There are many ways to make mistakes in faceting a gem but only a very few ways to facet a high quality gemstone.
On this site I will show you the most important facts (not all, I would have to write book about it...).

Precision Faceting


Meetpoint Accuracy
 
Have you been on a fair watching the stuff of a dealer and been wondering about prices? There are e.g. Spessartine Garnets, 2cts. good color, eyeclean for $ 10.- per piece while the next dealer offers the same for 10 times more. Try to cast an eye at both gems. To facet a high-quality gem takes the experienced faceter at least 3 to 4 hours and no one could offer highend-gems at bargain prices. Most of the cheap gems are faceted in a cheap way. You will hardly find any meetpoint faceted gemstones at low prices. The 1st pic shows a Goshenite 4.45cts. with a four-fold pavilion. Every facet in a fold has a different size and there are no meetpoints but "meetlines"...
 


On the left there is Fire Opal 4.85cts. with great color and less silk. I´m sure this gem would have deserved a better work, easy to see that the faceter has been very fast, although it is faceted for weight, see the numerous marks

To facet a gem with highest meetpoint accuracy is a hard and time consuming job even for designs like in this green Tourmaline from Namibia with 3.17cts. This design with all its parallel structures shows every little mistake obviously. The faceter did a good job, the lines are even and the light-return is high.

High-end "Rose de france"-Amethyst with 9.79cts. in a contrasty trillion design. The faceter put some high-lights for liveliness in it and also "dark" reflexes to increase saturation.